• <strong id="wkw2c"></strong>

          <source id="wkw2c"></source>

            <div id="wkw2c"></div>
            <strong id="wkw2c"></strong>
            <b id="wkw2c"><dfn id="wkw2c"><button id="wkw2c"></button></dfn></b>

          1. <samp id="wkw2c"><em id="wkw2c"></em></samp>
            液位計廠家,液位變送器廠家產品推薦
            3151靜壓式投入式液位變送器的調校需要注意
            信息來源: 液位變送器廠家 | 2020-06-01 點擊量: 3565

            3151型液位變送器是作為立足西北核心電路板和傳感器核心技術是獨立自主,在西安液位變送器生產廠家看來,投入式液位變送器是作為一種廣泛的應用在市政生活,化工處理,石化生產等行業有著廣泛的使用,西安華恒儀表制造廠家在設計和使用中為眾多生產廠家提供,經濟適用性強,復雜工況穩定性高,廣泛性好的靜壓式液位變送器./3151靜壓式投入式液位變送器的調校需要注意

            投入式液位變送器|高靜壓液位變送器|穩定型液位計產品說明|產品規格

            3151靜壓式投入式液位變送器的調校/投入式液位變送器安裝后該怎樣維護
                    (1)在流動介質和波動較大的介質中,安裝投人式平衡罩時,要附加熏錘(大于5kg)或固定在固體上,必要時應加防波管。被測量液體底部若有沉淀物,變送器平衡罩應提高,或加以過濾保護,以免堵塞。
                    (2)變送器量程可降低使用,但不準超量程上限使用。
                    (3)為防電磁輻射與雷電襲擊應將變送,器外殼接地采用屏蔽電纜或埋設地下電纜。
                    (4)使用一段時間后如發現誤差較大時,可把變送器的平衡罩拉出介質,串人電流表后調整零點電流應為4mA,調整后再插人介質中。
                    (5)安裝在敞開池或罐時可吊裝,變送器掛扳用M8螺栓固定,防腐容器一般用法蘭安裝。
                    (6)出廠時,零點(大氣壓時)為4mA,滿量程20mA已調好,請勿動。
                    (7)導氣管不得損傷漏進被測介質或漏氣,否則不能正常使用。
                    (8)在爆炸環境使用時,要選用專為防爆而設計的變送器意識別防爆類型的標志??晒┻x用WMY-A-EX系列.
                    (9)為避開現場腐蝕性氣體,根據脫離距離,讓中繼箱及傳感器不被腐蝕,可適當加長L2
            華恒變送器廠家研發出傳感器和智能電路板兩項核心技術,不僅所有產品的核心部件技術全部掌握,工業自動變送器廠家的精確度也在不斷提高,由0.2級提高到0.1級。還可通過對所掌握核心技術進行延伸,變形出測流量、測溫度的其他產品。/3151靜壓式投入式液位變送器的調校需要注意
              我們公司目前擁有三大技術實力,一是全隔離的智能電路處理單元技術,二是金屬電容傳感器的制造技術,三是全系列節流裝置的多參量技術。
            華恒變送器廠家憑借自身擁有的傳感器和智能電路板核心技術,可以根據客戶要求,低成本對核心技術進行延伸變形,實現個性化產品定制。主要產品有SMART(斯瑪特)系列壓力變送器、多參數變送器、流量器、溫度傳感器和物位(液位變送器廠家,為我國電力、石油、化工、冶金、水泥、礦業等行業提供了高性能價格比的工業自動變送器廠家產品./3151靜壓式投入式液位變送器的調校需要注意

             

            151 liquid level transmitter is independent as the core circuit board and sensor technology based on the northwest. In the view of Xi'an liquid level transmitter manufacturer, input liquid level transmitter is widely used in municipal life, chemical processing, petrochemical production and other industries. Xi'an Huaheng instrument manufacturer provides it to many manufacturers in design and use, Static pressure liquid level transmitter with strong economic applicability, high stability in complex working conditions and good universality

            Adjustment / maintenance of 3151 static pressure input liquid level transmitter


            (1) In the flowing medium and the medium with large fluctuation, when installing the throw type balance cover, it is necessary to attach a fuming hammer (more than 5kg) or fix it on the solid. If necessary, it is necessary to add a wave tube. If there is sediment at the bottom of the measured liquid, the balance cover of the transmitter shall be raised or filtered to avoid blocking.
            (2) The transmitter range can be reduced, but it is not allowed to exceed the upper range.
            (3) In order to prevent electromagnetic radiation and lightning attack, the transformer shall be sent, and the shield cable or buried underground cable shall be used for the grounding of the device shell.
            (4) after a period of time, if the error is large, the balance cover of the transmitter can be pulled out of the medium. After adjusting the current meter, the zero current should be adjusted to 4mA and then inserted into the medium.
            (5) When it is installed in the open pool or tank, it can be hoisted, the transmitter hanging plate is fixed with M8 bolts, and the anti-corrosion vessel is generally installed with flange.
            (6) When leaving the factory, the zero point (at atmospheric pressure) is 4mA, and the full range 20mA has been adjusted. Do not move.
            (7) The airway shall not be damaged or leak into the tested medium or air, otherwise it cannot be used normally.
            (8) When used in explosion-proof environment, the transmitter designed for explosion-proof shall be selected to identify the explosion-proof type. Wmy-a-ex series is available
            (9) In order to avoid corrosive gas on site, L2 can be lengthened appropriately according to the separation distance to prevent the trunk and sensor from corrosion
            Huaheng transmitter manufacturers have developed two core technologies, sensor and intelligent circuit board. Not only do they master all the core component technologies of all products, but also the accuracy of industrial automatic transmitter manufacturers is constantly improving, from level 0.2 to level 0.1. Through the extension of the core technology, other products for measuring flow and temperature can be deformed.
            At present, our company has three technical strength, one is the fully isolated intelligent circuit processing unit technology, the other is the manufacturing technology of metal capacitance sensor, and the third is the multi parameter technology of the whole series of throttling devices.
            With its own sensor and intelligent circuit board core technology, Huaheng transmitter manufacturers can extend and transform the core technology at low cost according to customer requirements to achieve personalized product customization. The main products are smart (SMART) series pressure transmitter, multi parameter transmitter, flowmeter, temperature sensor and level (liquid level transmitter manufacturer, which provides high performance price ratio industrial automatic transmitter manufacturer products for China's power, petroleum, chemical, metallurgical, cement, mining and other industries

             

            3151靜壓式投入式液位變送器的調校需要注意

             

            h華恒儀表央視轉載,西安液位變送器廠家產品宣傳,工匠精神宣傳
            ?
            掃一掃.廠家定制電話,
            好大 好爽 快点少妇_福利一区无码AV_AV天堂无码一区二区三区色噜噜_午夜三级A三级三点窝女
          2. <strong id="wkw2c"></strong>

                  <source id="wkw2c"></source>

                    <div id="wkw2c"></div>
                    <strong id="wkw2c"></strong>
                    <b id="wkw2c"><dfn id="wkw2c"><button id="wkw2c"></button></dfn></b>

                  1. <samp id="wkw2c"><em id="wkw2c"></em></samp>